1. Begin with the frame and sides. Attach three of the 12 12s after placing the 22’s down. After spacing them out by one from the bottom and three from the top, I centred the middle piece. Attach the three 32.5 12s to the back as shown once both sides have been constructed.
2. Next, fasten the back with the 32.5 13s. This will act as the shelf’s rail.
3. Next, begin assembling the 12 and 13 shelf slats. I utilised 4 per shelf and equally spaced them using a different scrap piece of 3/8″ wide wood. Make sure to begin with the front slat and move backwards.
4. I added the shelf slats in the following order: top shelf, bottom shelf, then middle shelf.
5. Add the 2 12 3/4 12’s on top last. This will serve as a handle and give it a polished appearance. The last six 12 by 12s were added to each end of the shelf as illustrated.
Paint Steps:
1. Before painting, be careful to smooth all the sharp edges and remove any extra dust.
2. Prepare the larger nozzle and paint in your Wagner Flexio 3000 Sprayer.
3. Spray the stand; read Wagner’s Blog for further information and instructions on how to accomplish that.
4. Apply a sealant to the plant stand when the paint has dried. Wagner Flexio 3000 Sprayer’s Detail Finish nozzle is perfect for this.
5. The new plant shelf should now be put up! It is situated on a small wall between my slider door and our hose, as I indicated earlier. It is quite effective at concealing excess pipes and electricity, and it also gives the wall a polished appearance.
Shop Supplies Here:
In this browser, JavaScript is not enabled at the moment. To access this content, reactivate it.
As you can see, I’m trying to keep my pots looking neutral. I’ve been gradually changing the appearance of my pots to either white, cement grey, or a rustic terracotta appearance. But this plant shelf has been a wonderful addition to my yard for less than $40. More importantly, painting and sealing it was much simpler thanks to the Wagner Flexio 3000 Sprayer finish.
To discover more about how to use the Wagner Flexio 3000 Sprayer, see their blog here. Additionally, keep coming back to see additional updates on the house. Enjoy!
About Katy
Hello! I’m a wife, a mother of three, a DIY junkie, and a lover of all things artistic! My blog, A Shade of Teal, is where I express my passion for design, home improvement, raising a family, and of course, teal! Enjoy!
What can I use as a plant stand outside?
30 Best DIY Outdoor Plant Stands to Display Your Plants
- The Top 30 DIY Plant Stand Designs for Your Porch.
- Plant stand with concrete block and wooden shelf.
- Repurposed plant stand with two drawers.
- Tall and lean vertical plant stand with tiers.
- Simple outdoor plant shelf stand made of cedar.
- Plant Hanger Welcome Stand made of wood.
What might I employ as a plant shelf?
Ideas for Diy Indoor Plant Shelves
- Contemporary Plant Shelf. Making this sleek and contemporary plant shelf is simple and only requires standard wooden planks.
- Plant Shelf That Hangs.
- Planter with a ladder.
- Simple DIY Plant Shelf
- Solid Wood Floor Stand
- Wheeled plant cart here!
- Plant Shelving Made of Wood Slices
- Perfect White Plant Shelf
How do you create shelves for hanging plants?
Your wood should be lengthened. To determine the size you need to cut, measure the interior of your window frame. My slice was 30 inches wide. Its size is little less than the window frame.
Make rope-holes. Where the holes are placed on your pieces of wood is a matter of preference. I decided to place the corners 1 inch from each edge. A 1/2 inch drill bit was employed. Make use of a drill bit that snugly fits your rope.
Make pot hole drillings. Determine the number of pots you want on each tier. Between the holes made for the rope, evenly space them. Ensure that the board’s holes are centred. If you don’t have a hole saw bit or don’t want to spend the money on one, holes can be made by hand using a jigsaw. I drilled holes to accommodate 4-inch terra-cotta pots using a 3 3/8-inch hole saw bit.
Make it smooth. Sand the interior of the holes for the rope and terra-cotta pots using the coarse-grit sandpaper. I sanded by rolling the sand paper up to fit it into the rope holes. made my life a lot simpler! * If you’re sanding the surface of the boards, be sure to work with the grain of the wood! Refine your work with smooth grit sandpaper to leave a good finish.
Stain your entire heart. Before staining, use a moist cloth to remove any sanding dust from the boards. Before applying stain, let the wood dry. Apply the stain of your choice according to the application directions.
Knot your ties. Greetings, boring part of this project. Tie knots beneath each board, beginning with the top board. Consistent space should be maintained between each board. If the spacing is constant, it’s alright if it’s not ideal right now because it will save you time later. Each whole shelf should have lengthy ends at the bottom to accommodate adjustments.
Post it up. I had to take down the blinds on my windows in order to hang my shelves. You might need to do this as well. Glue your eye hooks to the window’s frame. Make sure the eye hooks are in the stud above the window or in the window frame itself. If you drill a pilot hole that is just a little bit smaller than the eye hook, installing eye hooks will be simpler. Look into an anchor bolt for the wall that will hold the weight you require if you are not hanging from a stud.
go plant
The enjoyable part is now. You may put just about anything and anything on your new plant shelves. These two shelves have new items from Pistil’s Nursery, some hoyas, and cuttings of some of my vining plants (not sponsored but highly highly recommend them). For our window above the kitchen sink, I’m creating another of these shelves. That one will be filled with herbs!
How should I choose the wood for my outdoor shelves?
Because timber naturally resists insects and moisture, redwood is most frequently used in outdoor furniture. Due to the structure of redwood having low pitch and resin, finishes adhere to it quite effectively. Redwood trees grow slowly and are scarce, therefore this wood is not for those who care about the environment. Given its exquisite features, redwood is more of an opulent wood and can be expensive to get as lumber. Schumacher concurs “Redwood, a well-liked Western wood, is a great option for live edge furniture and any job requiring a big wide board. Similar to cedar, we seldom ever use redwood because it is a soft wood prone to dents, dings, and chipping. Similar to cypress, redwood can pull off during machining. There is very little movement, and the wood is quite attractive and cuts very nicely.”