In this hanging planter project, you’ll use a wood slice as the basis for your pot to sit on. You will attach a rope so it may hang after drilling a few holes in the wood slice.
Step 1Cut the rope to size
You will need to cut eight sections of rope into equal lengths in order to make this fashionable yet straightforward rope hanger.
Depending on the particular plant container you have selected, the appropriate length will vary. Generally speaking, the longer your rope needs to be, the bigger the pot. However, you’ll also need to add a bit extra to account for the knots and plenty extra to hang your planter with.
A few inches before the end, secure all eight strands with a tight knot.
Step 2Secure the rope to the base of the pot
Place the knot in the center of the pot after turning it over, and then split the strands into four groups of two. The bottom of the pot will be divided into equal parts as a result.
Small strips of adhesive tape should be used to fix these strands in position. Then, just past the base’s edge, tie a little knot in each group. These knots ought to be apparent once the job is finished and the pot is placed back upright.
Step 3Create the knots
You are now prepared to begin tying the rope plant hanger together. One rope from the first group and one rope from the next group should be taken, and they should be tied together in a knot. Be sure to place this in the middle of the two upper knots. Continue until the first row is finished, traveling all the way around the pot as you go.
Pull the rope very gently to remove any slack, then use a small piece of sticky tape to hold each knot in place. Although the rope will be kept in place by the tape, it will make succeeding rows easier to knot together when it is eventually removed.
Continue by tying the next row of knots in the same manner. Again, the size of your pot will determine how many rows you need. However, we advise leaving a 1/2 inch space between the last row and the top edge for all projects.
Step 4Tie it together and hang
Last but not least, flip the pot over one more and tie the eight rope strands together in a single knot. You can tie the knot at any desired height. Just make sure that all of the ropes are the same length (therefore allowing your pot to hang level). If they are, cut off any extra, and take off all the adhesive tape.
You have a few alternatives for hanging your brand-new macram plant holder. The rope can be hung directly from the screw hook if you like. Alternatively, you could attach the rope to a wooden ring and hang it there for a more tasteful and polished look.
Start making your rope hanging basket today
Ready to begin knotting? Make a chic rope hanging basket for your house or yard by selecting your succulent and stocking up on rope supplies. Also keep in mind that we always like seeing our customers’ creations! We’ll be sure to include some of the best images of the macram plant holders you make using our ropes, strings, and twines on our website and social media pages if you send us some pictures.
What kind of material are plant hangers made of?
Use this easy DIY macrame plant hanger tutorial to dress up your indoor plants and transform them into a suspended forest.
- 1. Select the macrame cord. Go to your neighborhood craft store and choose the cord type you’ll need for your project. You can pick from materials like hemp, jute, or cotton twine or cords. Because this is how you’ll make your plant hanger, choose a cord material that is flexible and simple to tie knots with.
- 2. Shorten your cords. The size of your planter will affect both the number of cables you need to utilize and their length. While larger planters could require eight cords, smaller planters might only need four. The precise length will also vary depending on how high or low you want to hang your planter.
- 3. Select the knot. You can create your plant hanger using a variety of fundamental macrame knots, including the square knot, wrapped knot, and clove hitch. Depending on the kind of macrame plant hanger pattern you select, the knots you employ may vary. Feed your cords through your ring, fold them in half so that twice as many cord ends hang downward, and tie a simple but strong knot to fasten the top of your plant hanger. To secure the bundle of cords together, wrap a second, shorter piece of cord around it several times and tie a knot.
- 4. Tie several knots. Measure down to where you want the planter’s lip to be from the top of your knotted cords. You will begin the first level of knots here. Divide the number of cords you have evenly among the new cord bundles you make by separating your original bundle of cords. Use the knot of your choice to connect each bundle.
- 5. Join all of your knots. You can make a type of knotted netting by taking one cord from two nearby sets of knots and tying it together. Repeat this procedure with the other cords.
- 6. Lock up the planter. To secure the planter in place, set the planter inside the circle you’ve made by gathering the ends of all the cords and knotting them together. You can hang your planter from a bracket or hook you’ve fixed to the wall or ceiling using the ring.
I want to make a macrame plant hanging, how much cord do I need?
Making your own plant hangers in the style of boho chic is stylish and easy with macram, the knotting technique for rope. It’s a trend from the 1970s that has come back, and this time it’s even better. If you love plants, you’ll adore how these hangers will display your plants both indoors and outside.
Making your first DIY macram plant hanger could seem difficult at first, but after learning the fundamentals, it’s really fairly simple! Today, we’ll go over some fundamental knots and patterns that you can use to create a macram plant hanger.
The three fundamental knots we’ll use in the tutorial are as follows:
- Round knot
- Spiral or half-square knot
- Knot loop
If you’d need extra experience with these before you get started, try out this useful instructional on fundamental macram knots. We’ll go through each type of knot in the video.
Materials:
- 8 cotton cords totaling 15 feet in length (3.1mm thick)
- two brass rings
- two 5 foot lengths of rope
Do curtain rods have the strength to support plants?
Rolling Stone might earn an affiliate compensation if you use a link on our website to buy a product or service that has been independently reviewed.
Indoor plants are a popular and simple method to add brightness to your room while also enhancing the air quality. Hanging plants, however, can frequently prove to be a little difficult than they seem, especially if you live in a rented place and don’t have the option of drilling holes in your walls and ceiling. It’s easy to soon run out of surface area to put them in. Fortunately, you can acquire a few pieces of equipment to make it simpler. Whether you can use a drill or if you need to get craftier, here is our guide to hanging indoor plants.
How to Hang Your Plants in Any Space
When using hooks, make sure the surface is sturdy enough to hold the hook in place after you’ve hung your plant on it without disintegrating. If you do have the ability to do so, pick simple hooks that screw into the wall or ceiling.
Tension Rods: If you can’t (or don’t want to) use power tools, a set of straightforward tension rods can be a quick and simple fix. These can be put in any window or door frame, as well as any room in the house where two walls are reasonably close to one another. Make sure to check the rod’s weight restriction before attempting to hang anything from it. The majority of top-notch tension rods can support up to 30 pounds. If you need to hang plants that weigh more than 30 pounds, you can get creative by stacking many rods on top of or behind one another.
Garment Racks: Using a tall garment or clothes rack, preferably one that is stylish and without wheels, is a unique method to hang plants in your home. This makes a lovely green accent wall while still letting in natural light, especially for trailing, ivy-like plants.
Interior Trellis: For your plants, you may also get an indoor trellis or even a rustic-looking ladder that leans against a wall. This can be used as a surface from which to hang small pots or to grow climbing plants.
Without a hook, how can plants be hung?
You can simulate ceiling-hung plants without really hanging them from the ceiling by using metal tension rods that extend from wall to wall.
Where two walls are close enough together, a tension rod with non-marring rubber tips can be mounted almost to ceiling height. Using a shower tension rod, you may span openings in walls, skylight frames, and hallway ends.
Standard tension rods for showers have a range of 41 to 72 inches. Product-specific weight capacities range from 10 to 30 pounds. For room divider curtains, extra-long tension rods can extend to 120 or even 160 inches. That is a length of 10 to 13 feet, or about the width of a small room.
Just keep in mind to buy a tension rod that is longer than the span. The rod must typically be 2 inches longer than the desired spread.
Contrary to curtain tension rods, which frequently have weight capacities below one pound, shower tension rods are thicker and more durable.
Can you hang plants on a curtain rod?
Yes! Plants can be hung from a curtain rod. I have mounted curtain rods for actual curtains, not for plants, and I have several plants dangling from them. One for two. Even a curtain rod can be transformed into a hanging plant pole. I just decided against it because they are more expensive than a pipe or a big wooden dowel.
Whether you’re using a curtain rod for drapes with plants in them or just for plants, there are three things to keep in mind! These are them.
Weight rating of the curtain rod
If your curtain rod has a weight rating, check it. Many of the thinner curtain rods weren’t designed to support a lot of weight. It’s generally wise to update to a curtain rod that can support a little bit more weight if you find your curtain rod beginning to bow anywhere where your plants are hanging.
Strength of the curtain rod
Numerous curtain rods can be extended. The central portion of the rod, however, can become weak when they extend to their maximum length. Try to avoid using your curtain rod’s maximum extension if it is extendable. Add a third curtain bracket in the rod’s midsection for support if you intend to use the entire expanded length of the rod.
Mounting hardware and mechanism
In relation to curtain brackets, the mechanism and mounting supplies you choose to mount the curtain rod also matter. For instance, be sure to use strong brackets and drywall anchors that are weighted for the proper amount of weight if you’re mounting them in drywall.
The brackets should be mounted directly into studs, although this isn’t always possible. So it’s excellent if you can. If you can’t, make sure to use strong drywall anchors in conjunction with your screws.
Can yarn be used to build plant hangers?
Generally speaking, hanging plants cost more than their basic, potted counterparts. Make your own potted plant hangers from spare yarn scraps. Because yarn is available in so many different shades, tones, and textures, it’s simple to match your plant hangers to the furnishings in any room of your house. Simple knots can be used to make a strong, useful, and lovely item of home décor.
For this project, go with a thick, bulky-weight yarn. The best fibers for ordinary wear and tear are synthetic fibers, such acrylic. Wool may warp in the presence of water and friction, and cotton loses its elasticity with time.
- Generally speaking, hanging plants cost more than their basic, potted counterparts.
- Simple knots can be used to make a strong, useful, and lovely item of home décor.
The length of your plant hanger should be measured. This is the distance between the bottom of the plant’s pot and the hook from which you will hang the plant.
Add five times to this measurement. To this size, cut six pieces of bulky-weight yarn. You would need six lengths of yarn that are each five feet long to make a one foot plant hanger.
The yarn bits are folded in half. A sizable metal O-ring should be moved across the yarn strands until it reaches the center fold. Use a hitch or slip knot to tie the yarn beneath the ring to keep it in place.
- The length of your plant hanger should be measured.
- A sizable metal O-ring should be moved across the yarn strands until it reaches the center fold.
Heavy duty yarn should be divided into strands. There should be twelve given that they are folded in half. Make three groupings of four strands out of the strands.
Use a bulldog clip to secure the metal ring. A safe surface, like the edge of a desk, table, or couch, is ideal for mounting the bulldog clip.
Choose a single quartet of strands. This group should be tied off from the other yarn strands using an overhand knot to keep it together.
Heavy duty yarn should be divided into strands.
Using two strands held together as one, tie two square knots with the yarn fragments in the clipped group. The knots should be positioned such that they meet the top edge of the flower pot. Avoid tightening the square knots; they should be firm but loose enough to allow you to still see the pattern of the knots’ construction.
Use two strands that are held together as one to tie two square knots in each of the remaining four-strand groups. Place these knots so that they meet the top edge of your flower pot. You should be able to see the design of the knots if you don’t tug too hard on the knots. The yarn should now be divided into three portions, each with one overhand knot and two square knots.
- Using two strands held together as one, tie two square knots with the yarn fragments in the clipped group.
To the bottom of the flower pot, weave all of the yarn strands, interlacing and adding knots as you see fit. Any additional knots you tie in the yarn strands are just ornamental; they are not necessary. Put a square knot or hitch knot on each of the strands and secure them at the base of the pot.
The yarn strands’ ends should be carefully cut or left hanging to create a stylish tassel.
To add glitz and glamour to your yarn plant hangers, string beads onto the strands of yarn before knotting.
Create a crochet chain for each initial strand of yarn if you are skilled in the chain stitch of crochet to add a more twisted, beautiful touch.
Make mistakes or explore with knots without fear. Knots are always reversible. As you make your plant hangers, take some time to experiment with the yarn.