How To Make African Violet Pots

The traditional red earthenware flower pot is the best planter to use, yet planters are a staple of the potter’s toolkit. However, certain plants benefit from having unique pots designed specifically for them. African violet planters built by hand that are now for sale have an inner pot where you plant the violet and an exterior pot with water in it. In this manner, you can water the plant from underneath without damaging its delicate leaves. In contrast to employing a porous olla within a planter to offer a consistent supply of water to the plants surrounding it, the notion holds that the inner pot is porous so that water can soak through it from the outside pot.

However, you’ll run into trouble if you utilize the same clay for the inside and exterior pots. Let’s imagine that you develop stoneware using fire. Since stoneware that is heated to maturity becomes vitrified, or non-porous, the inner pot won’t be porous. The outside pot will also be permeable if you use earthenware clay or fire your stoneware at a lower temperature. It will destroy your floor or furniture by leaving a wet stain on any surface it sits on. As even minor crazing in the glaze may cause it to leak, you cannot rely on coating the exterior pot to keep it from leaking. Over time, you can also anticipate that the glaze will craze. You could fire the outside pot to vitrification and fire the inner pot to a lower temperature, but it would cause the two pots to shrink at different rates, making it difficult to get them to fit together nicely. Not impossible, but challenging. If you use stoneware for the outer pot and earthenware clay for the inside pot, you’ll run into the same issue. My easier option is to make a hole in the inner pot so that water can seep in.

Choosing the Size of Your Pot

These pots can be made in any size, from that of a mug to around a gallon. The ones I’ve seen are often tiny, made for newly propagated plants, but it seems more practical to use a pot made for an established plant. Use 2 pounds of clay each pot for a planter of average size. Making the inner pot comes first.

Open up one clay lump in the center, leaving a floor that is 1/4 inch thick. You shouldn’t leave the bottom of this planter thick because a foot is not necessary. Pull the wall up, allowing it to flare slightly, and create a flat floor approximately 4 inches broad. Use a soft rib to push the top inch of the rim out a little wider once all the clay has been pulled up into the wall. This will create a ledge at least 1/4 inch wide that can rest on the rim of the outer pot (1). The outer pot will fit more easily the wider you make this ledge. The pot should now exactly resemble a traditional ceramic flower pot. Just below the ledge you just made, measure the diameter of the pot using calipers (2). This measurement should line up with the inner edge of the rim of the outer pot. The outer pot must be taller than the height of the inner pot measured to the ledge. After taking these measurements, I prefer to flute the inner pot’s rim to give it a floral appearance and make it stand out from the standard design (3). In order to prevent the pot from being distorted while I’m doing this, I use a rib. Now, disconnect the pot from the wheel by running a wire below it.

Throwing the Second Pot

Toss the outside pot with the second lump of clay. To ensure that there is space for water surrounding the inner pot, this pot will have a rounder bowl shape. Once more leaving a floor that is 1/4-inch thick and roughly 4 inches in diameter, center the clay and open it up. As you raise the walls, make sure they gently curve upward and reach a height that is at least equal to the inner pot. Check the diameter of the rim’s interior with the calipers once you have reached the necessary height (4). If the inner pot’s diameter inside the rim isn’t very close to its caliper measurement, it might merely fall through and rest on the outer pot’s floor rather than perching on the rim. To free the pot from the bat, run a wire underneath it.

Try nesting the pieces as soon as you can pick them up without warping them (5). You might be able to trim a little from one or the other pot if the fit isn’t perfect. Without pruning a foot, remove any extra weight from the base of each pot.

Symmetrical Spouts

Make two tiny spouts slightly below the rim of the outer pot once it has become a little stiffer, resembling tiny pouty lower lips. You can fill the pot with water using these spouts without removing the inner pot.

Put the pot back on the wheel and, using a needle tool, draw a line all the way around, about an inch below the rim, to create the spouts. Now, on this line, make two markings directly across from one another using a decorative disk (6). At each point, make a slit that is about 11/2 inches broad. Now, using a finger that has been wet and pressing from the inside, gently push the lower margins of these slits outward (7). Stretch the clay until you have two triangular lips that are big enough for a watering can’s spout. You want two spouts, why? It’s partly for symmetry, but it also makes it possible to insert your finger into one spout while filling the other with water so you can gauge when the water level is appropriate. Before continuing, sponge the spout region to make it smooth and improve the spout shapes.

The inner pot must be punctured in order for water from the outside pot to seep inside. Turn the pot over after it has reached leather hardness and use a decorative disk to mark out a pattern of holes on the bottom and sides (8). The precise number of holes is unimportant, so I drill 8 very tiny holes on the bottom and another 8 just above the pot’s base. The roots of the plants will be content as long as they can absorb water when they require it. Dry the components together to prevent warping (9).

Glaze the inner and exterior of the outer pot after they have been bisque fired for aesthetic and cleaning ease reasons. Since the interior pot won’t be seen, you only need to glaze the rim because you don’t want to risk glazing the microscopic holes. You should fire the two components together if they fit tightly together. Make sure to wax the outer pot’s rim first.

Time to Plant

Plant one African violet in the inside pot of your planter, preferably using African Violet potting soil. Place the two pots together, then fill the outer pot using one of the spouts while keeping an eye on or feeling for the other spout’s water level to rise. Your violet should thrive if you water it in this way around once a week.

Do African violets require deep containers?

age of development The violet is growing in a pot that has a diameter that is one-third that of

violets. Rarely does an adult African Violet require a pot bigger than 4 or maybe even

The neck or primary stem of the plant is revealed after the older outer leaves wither and fall off.

This indicates that the plant needs to be repotted. Crash off almost all of the

callous. To allow the stem to eventually develop new roots, you must remove the callous.

plant in a plastic bag big enough to hold it, then zip the bag shut.

If you just allow one rosette of leaves to develop on one root system, it will grow more densely.

Keep the roots of plants with a root system attached. According to

Are African violets better suited to clay or plastic pots?

You want to plant some African violets in pots around your house because you are cultivating them. There are many various types of plant pots available, but which one is going to work best for your African violets?

I prefer pots with two layers since you can add water to the bottom of the plant without worrying about it becoming waterlogged. You can discard the remaining water until it is time to water the plant again once it has received enough to make the soil at the top of the plant moist. The flower will self-water itself if you leave a tiny bit of water at the base of the pot, which is a terrific tool to use when you have to travel and no one to water your plants.

You can select from a variety of materials, which include the following:

  • Clay vases Although these are not the prettiest pots, their high porosity can help your African violets drain their water.
  • Pliable pots
  • The majority of these pots are well-draining pots that your African violets will adore, but especially the ones with saucer bottoms. Just be careful not to let the plant’s base become wet.
  • Ceramic PotsThis kind of pot has two pieces, making watering simple. They are very vibrant, which can really enhance your growing area.