Let’s face it, everyone like a houseplant that grows rapidly. Rubber Tree plants (Ficus elastica) are extremely popular in our houses for this reason. If you give it a good home, it will flourish…a lot. Rubber Trees, on the other hand, don’t branch easily if left to its own devices, so you can end up with a single stalk extending from floor to ceiling if you don’t intervene.
Is it possible to make a Rubber Tree branch out? Because branching rarely happens naturally in Rubber Trees (especially in younger plants), it is required to prune the plant to encourage branching through nodes on the stem. The plant will begin to create new branches below the cut if you pinch or clip back new growth.
This is not a practice for the faint of heart. We try our hardest to take care of our houseplants and keep them healthy, so the concept of chopping back otherwise thriving plants is a little frightening. Pruning back Rubber Tree stems, sometimes severely, is, by far, the most effective strategy to encourage branching for a fuller, bushier appearance.
How do you make a rubber plant bushier?
Take a step back and take a look at your rubber plant. Consider its location and current growth when deciding how you want it to look.
If your rubber plant is on a table or shelf where there isn’t much room for it to develop, it’s usually best kept as a short, circular shrub.
Pruning lateral branches will encourage new growth to fill in the plant’s centre portion, so pick a size you can work with and then let it fill in on its own.
Step 2: Remove any branches which seem out of place.
Begin by clipping back any lower branches that appear to be growing straight out horizontally or that are interfering with the plant’s ideal shape.
Some branches will grow in unusual directions, twisted, or at a significantly faster rate than others. To keep the plant looking tidy and appealing, remove these.
To keep the plant from looking overly dense, trim some branches and leaves from the middle section, but this is a matter of personal opinion.
Step 3: Cut to your desired height.
Trim the top set of leaves before the node after your rubber plant has reached the appropriate height. By cutting before the node rather than after it, you’re essentially leaving a stump. The plant will no longer be able to send out any more vertical chutes as a result of this.
Trim the top of the rubber plant when it reaches a maximum height of four feet for a more compact shrub-like shape. Instead of growing tall and narrow, this will encourage the plant to grow more horizontally and produce a more rounded form.
Step 4: Encourage leaf coverage by pruning often.
As previously said, caring for a rubber plant as a bushy shrub needs a little more effort than caring for it as a larger tree-like houseplant. Pruning is required to maintain a bushy rubber plant.
When a cut is made after a node, one or two additional branches will begin to grow from the location where the cut was made. Cut them back as well after the plant has recovered from the previous pruning and sent out some new chutes.
You may manage how thick and bushy the plant develops by trimming the new lateral growth on a regular basis.
Step 5: Propagate new cuttings back into the pot.
Propagating rubber plant cuttings is simple and straightforward. You can produce a more shrub-like appearance by inserting these cuttings back into the pot of your rubber plant, which will assist to fill in the bottom areas of the plant.
After pruning, cut branches can be directly transplanted back into the same pot as the original plant, or they can be rooted first in a glass of water.
How do you shape a rubber plant?
Take a step back and examine the contour of your tree to get a sense of how you want it to appear. Make your cuts immediately above a node, which is where the leaf joins to the stem or where another stem branches off, on the rubber tree plant. Pruning just above a leaf scar is also an option.
Remove roughly a third to half of the plant’s branches, but don’t remove any more leaves than is required. New growth will emerge from these wounds gradually, so don’t be surprised if the plant appears a little scrawny after pruning.
How do you make a ficus branch?
The node on ficus is directly above each leaf. They’re easy to recognize since a thicker ring goes around the stalk in the same place as the node. When the new growth is removed, the node(s) closest to the top begin to grow and develop into a branch.
What can I do with a leggy rubber plant?
Rubber plants that lose their leaves might become leggy, which means they have no leaves on the lowest half of the plant. Rubber plants only sprout leaves at the top of their stalks, not at the bottom. As a result, there is no way to make a plant leaner.
Replant lesser stalks in the planter with the larger ones to make your Rubber Plant appear fuller. This will make the plant look bushier by filling in the lowest naked space.
How do you take cuttings from a rubber plant?
Rubber tree propagation can be untidy since the stems leak a sticky, latex-rich white sap when cut. Make sure the work surface is well-protected. To avoid disease spread, thoroughly clean the area to eliminate any other plant waste or soil. When harvesting cuttings from a rubber tree, it is recommended that you use protective gloves because the sap can cause skin irritation if it comes into touch with your skin. Before you begin propagating, double-check that you have all of your equipment and supplies on hand.
How do you promote branching?
To encourage branch growth, make heading cuts on young trees. If you use heading cuts on wood that is one year old or older, you will encourage the creation of waterspouts. To a healthy growing point, cut back the lateral branch or main upper vertical stem. Make a 1/4-inch cut just above a lateral bud.
Why are the leaves of my rubber plant falling off?
A change in the light is a common cause of a rubber plant losing its leaves. This frequently occurs when you move your rubber tree plant inside from the outside, and the change can result in the rubber tree leaves dropping completely. When the light levels shift from summer to fall, a few rubber tree leaves may fall off the plant.
When you bring the rubber tree indoors, acclimating it gently and shining a few plant lights on it can assist keep the light levels up and prevent the rubber tree from losing leaves.
Pests – Another typical cause of rubber tree plant leaves falling off is pests. Rubber tree plants, in particular, are subject to scale bug infestations, which cause the leaves to fall off unless the plant is treated.
How do you branch Ficus Elastica?
Breaking apical dominance is the most typical approach to fix a rubber tree that won’t branch. In layman’s words, this entails eliminating the top growth on the main stem, which re-directs a hormone called auxin downward, encouraging branches to sprout further down the stem. When the plant is young, this is the perfect time to do it. Disturbing the leafy top canopy of older plants is bad for them.
When pruning a rubber tree for branching, do so from March to October when the plant is actively growing. The top cut is the most crucial. Remove as much of the stem and leaves as you want. The bits you remove can be rooted and used to grow new plants with patience.
Cut a leaf scar (a line where a leaf once grew) or a leaf node at 1/4 inch (6 mm). Sharp pruners can be used to nick or lightly slice the leaf scar to encourage the growth of a new leaf.
Can I cut the top off a rubber plant?
Rubber plants don’t require much pruning other from removing dead or dying leaves. Keep the following in mind when shaping your plant: don’t take off the top until it reaches the appropriate height. Your plant will branch out if you chop off the top. You can always chop back unwanted branches to get the form you want. Pruning is best done in the spring or summer, but it is not required.
Do rubber plants like coffee grounds?
Although coffee grinds have an immediate good effect on rubber plants because helpful soil bacteria use it to make nitrogen, too much of it will kill those same microbes. Instead of coffee grounds, use an appropriate fertilizer to feed a rubber plant.