From the 3/4″ × 3/4″ square of hardwood, cut 4 legs and set aside. My legs were chopped to be the same height as the pot the stand could support.
Step 2: Cut The Wood For The Plant Stand Platform
To support the potted plant, the platform will be made from three 1 x 2 pine pieces that are cut into an X shape.
Piece A: Cut one piece to the desired plant stand width (the widest part of your pot.)
Cut a second piece that is identical to piece A but thinner than piece A for pieces B and C. To get pieces B and C, divide that piece in half.
Step 3: Drill Holes For The Platform Piece
Drill two holes through component A that are precisely in the centre, each the size of your wooden dowels.
Mark the holes with a pencil after aligning the end of component B with the openings. Then, drill holes into your marks so that your dowels may fit halfway through.
Step 4: Drill Pocket Holes For Legs
On the underside of the platform, where the legs will attach, you will drill pocket holes.
Drill pocket holes on the edge of each short piece of your platform (on the opposite end of your dowels) and on one edge of both of your long piece’s ends using a Kreg Jig to begin.
Step 5: Assemble The Platform Piece
Place the wooden dowels into the shorter pieces with a dab of wood glue, then into the long piece on both sides to form an X, ensuring sure that all pocket holes are on the same side.
Step 6: Determine Your Plant Stand Platform Height
The size and shape of your pot will determine where (and how high) you place the platform of your plant stand (the x you just constructed) on the legs.
With a friend holding your pot in position, hold your platform with one leg on each of the two opposite sides so you can see where you want the top section of each leg to touch your pot. You’ll notice that the point of contact between the top of the legs and the pot changes as you raise and lower the platform.
After that, align each leg and make a mark on each one. (The quantity of wood extending up the side of my pot will be on the left, and the legs will be on the right.)
Step 7: Attach The Legs
Make sure the pocket hole is facing the bottom of the leg when you align the end of the platform piece with the marks you drew.
Repeat for each leg, fastening the platform to the leg piece with a Kreg screw.
Use a moist towel to wipe away any adhesive that has leaked. (If you don’t, the stain won’t penetrate the wood there.)
(optional) Step 7: Stain Your Outdoor Plant Stand
You spent time building a plant stand, but if you plan to put it outside, you’ll want to be sure it can withstand the weather.
Give your plant stand a coat of stain or paint to preserve the wood and make it look attractive. (I applied Dark Walnut MinWax.)
All that’s left to do is fill the pots on your own outdoor plant stand with lovely plants!
Here are some more incredible West Elm ripoffs made by some extremely skilled women. To get all the information about these lovely creations, click on the links below this picture!
What can I use as a plant stand outside?
30 Best DIY Outdoor Plant Stands to Display Your Plants
- The Top 30 DIY Plant Stand Designs for Your Porch.
- Plant stand with concrete block and wooden shelf.
- Repurposed plant stand with two drawers.
- Tall and lean vertical plant stand with tiers.
- Simple outdoor plant shelf stand made of cedar.
- Plant Hanger Welcome Stand made of wood.
How is a trellis frame constructed?
2. Join the edges of two of these 3-foot sections and two of the 6-foot pieces to create a rectangle “image frame form.
3. Use wood screws to join these four parts together. The other 3-foot and 6-foot sections should then be used. Therefore, you now have two “on the trellis’s sides.
4. Spread out enough hardware or fencing material to completely cover one side. Staple it to the frame using your stapler. Advice: To prevent the hardware cloth from sagging in the middle, pull it taut when you staple it to the frame.
5. Continue with the other side or frame.
6. To join the two frames, screw in the two hinges at the top of the frame. Advice: Carry out this action with the two frames lying open on the ground.
Making the “first dividing a second 6-foot piece into two 3-foot sections.
8. Next, slice the 3-foot piece in half diagonally to make two “pieces of feet The pointed side will stick out into the earth and tip downward.
9. Repeat with the other two pieces of foot.
10. Attach the four foot pieces with screws to the frames.
Get the strategy To help you, I’ve posted a schematic and instruction sheet on my blog. Download it from this page. On request, high-resolution images are available.